Free Engine

Covid-19 Operating Changes 

Orders are still being shipped, two days per week. Ground only.
Phone lines have been routed to employees at home. We highly encourage customers to order on our web site and email us at [email protected] with questions.
If you get a busy signal, please try later. Thanks for your patience.
You Can Also Live Chat With Us or Go to facebook.com/mudskippermotors to message us

Thank you for your continued business during this unprecedented time




Profile Informations

Login Datas

or login

First name is required!
Last name is required!
First name is not valid!
Last name is not valid!
This is not an email address!
Email address is required!
This email is already registered!
Password is required!
Enter a valid password!
Please enter 6 or more characters!
Please enter 16 or less characters!
Passwords are not same!
Terms and Conditions are required!
Email or Password is wrong!

Mud-Skipper PTFE Hull Coating - 80 sq ft

Mud-Skipper PTFE Hull Coating - 80 sq ft

Availability: In stock


Quick Overview

Mud-Skipper PTFE Hull Coating


Mud-Skipper PTFE Hull Coating
The ultimate slick hull coating system for all small boats.
Jon, Duck, Air, Drift, Jet, Mud and pontoons.




 Combines pure PTFE with the toughness of a water based epoxy, and ceramic for abrasion resistance.

One coat application - takes minutes to apply

Chemically resistant to fuel spills and salt water.
Improves handling, improves speed!
Seals joints, rivets and seams.
PTFE aids lubricity and makes cleaning easy. Minimizes fouling by algae etc.
Easy to apply. Non-drip formula.
Notched applicator supplied to layer the system on evenly
Can be reinforced with Kevlar, carbon fiber and glass fiber, especially if over old repairs.
Safe on aluminum - no corrosive copper content.

How to prepare the surface?
Surface preparation is the key to success in any application.
Use a power washer to remove all algae, grime and surface contaminants.
Incorporate a good detergent to remove any oils, greases and fingerprints etc.
It’s best to remove all old paint and rough up the surface with a sanding disc or belt sander.
If there are several layers of paint, consider using a paint stripper then a high pressure power washer.
Lightly sand to roughen the surface to aid mechanical adhesion. Do not use an angle grinder with a sanding pad. This tends to dig into the aluminum skin and leave marks. An orbital sander or light sand blasting is preferred.
Be careful not to sand off rivet heads, but flattening the tops of them is ok.

Carry out any repairs to loose rivets, splits, holes etc If there are open joints, these should be fixed by riveting them shut or hammering them together. Use Casweld Aluminum brazing rods for hole repair.

If you are careful with the roller, there is no need to mask as the system is quite thixotropic and doesn’t run. If you prefer to, mask up all edges, use blue painters masking tape and remove before the coating cures.

The application needs to be done on a cool to warm day 60-70 degrees, low humidity and in the shade. Surface of the metal should be on the cooler side, but not cold as this will make the resin harder to work.

Mix the two parts of the Mud-skipper Hull Coating System together thoroughly and apply quickly and evenly with  the applicator provided or with a notched steel trowel using the fine tooth. This is merely to get an even coat on the job. As soon as you have spread out the material, run a paint roller over the surface with quick strokes to 'pull' the material to produce an orange peel effect. The more orange peel texture you have, the faster you'll go.

This operation should be done quickly as you have about 15-20 minutes at 70 deg f.
Remove the masking tape while the system is still soft, about an hour after application.
At this point, if the weather is dry and sunny, bring the boat into the open so it can warm up the aluminum. This will speed up the curing process.

Clean up using water with a dish washing liquid detergent.

Boats up to 100 sq ft approx

You need:-

A 4" Whizz Roller from Lowes or Home Depot. Get the Oil Based ones. Don't buy bigger rollers as they suck up too much material.

Orbital Sander and 120 grit sand disks/pads

Detergent and a power washer is preferred.

Masking Tape. Latex Gloves

Kit for up to 18’ long  Boats 80 sq ft approx

Kit comprises
2 pints Mud Skipper Hull Coating part A
1/2 pint Mud Skipper Hull Coating part B

Video Testimonials & Reviews (Upload a video of our products in use and get free propeller(s). Twisters get one free prop. Longtails get 3 free props. Video must have Mud-Skipper in title, must show kit in water, in action and must be at least one minute long.)

Video Testimonials & Reviews (Upload a video of our products in use and get free propeller(s). Twisters get one free prop. Longtails get 3 free props. Video must have Mud-Skipper in title, must show kit in water, in action and must be at least one minute long.)

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

My Cart

You have no items in your shopping cart.